top of page

MoTec PDM40: The new benchmark in intelligent power management


With the PDM40, MoTeC once again sets the benchmark: 40 main outputs, 200 A rated current, integrated data acquisition, and visual, block-based programming in Simulink style – all in a single, IP67-rated enclosure. Available from Q2 2027 – also from Maptec.


MoTeC PDM40 - the new benchmark in intelligent power management in motorsport and industry

At PMW Expo 2026 in Cologne, MoTeC presented the PDM40 to the public for the first time. The PDM40 combines high-current power distribution, vehicle control, data acquisition, and communication on a single platform. Functions that previously required additional control units, relays, or loggers are now integrated into a single device.

In this article, we present the most important functions, show why the new programming environment massively reduces setup effort, and where the PDM40 also demonstrates its strengths outside of motorsport.


New to PDM? We explain the basics – what a PDM is and when it's worthwhile – in our guide: What is a PDM – and why do I need one in my vehicle?


MoTec PDM Power Management



Hardware: more power, more channels, less peripherals

The PDM40 is designed for a nominal current of 200 A and can handle significantly higher peak currents for short periods. The 40 main outputs are configured as high-side and half/full bridge outputs in various current classes – each with current measurement, programmable protection, and soft start and soft stop.

The half-bridges support PWM and motor-synchronous control. This allows the PDM40 to directly drive DC servo motors, current-controlled solenoid valves, or two-stage windshield wiper motors – without external H-bridges or relays. Most outputs detect open circuits, short circuits, and overcurrents and react accordingly according to a defined strategy.

feature

PDM40

Rated current

200 A (higher transient peak currents possible)

Main exits

40 × High-Side / Half and Full Bridge, with current measurement

Low-side outputs

8

Sensor power supplies

4 × 5 V, with overcurrent protection and current monitoring

Entrances

Analog and digital, switchable pull-ups/-downs, 2 × wideband lambda

Internal sensors

6-axis IMU (16 g), real-time clock

Operating voltage

All functions down to 6V

Standby

Separate standby input, < 1 mA quiescent current

Power connections

2 × Surlok Plus® 8 mm, 35/50 mm², Plus and Minus configurable

Signal connector

1 × 60-pin, 1 × 94-pin (fully equipped, waterproof)

Housing

Fully sealed, IP67

Dimensions / Weight

174 × 171.5 × 47.3mm / 1030g

MoTeC PDM 40 Output Specifications
MoTeC PDM 40 input specifications
Hinweis: Die Spezifikationen sind gemäss MoTeC vorläufig und können sich bis zur Markteinführung ändern.

The power management feature is particularly relevant in practice: A dedicated standby output directly controls a battery disconnect switch. The PDM40 can be flexibly woken up via CAN, Ethernet, standby inputs, time, or the IMU. Reverse polarity and transient protection are integrated.



Programming: visual, block-based, in Simulink style

The biggest step forward lies in the software. The PDM40 is configured in MoTeC Tune 1.6 – the same environment used to tune the M1 engine control units. Therefore, anyone working with M1 uses a single tool for both ECU and PDM.

At its core is the new COMPUTE subsystem: a visual, block-based programming environment reminiscent of MATLAB/Simulink. Logic is no longer distributed across tables and condition lists, but rather structured as a signal flow – inputs, operators, timers, state logic, and outputs are placed and connected as blocks. This offers us as engineers three tangible advantages:


  • Traceability: The signal flow is readable at a glance. Even a configuration created by someone else is easy to understand.


  • Complexity without workarounds: Multi-stage shutdown strategies, load management or pump controls with hysteresis can be cleanly mapped instead of being distributed across multiple channels.


  • Maintainability: Changes to a function remain local and are visible – crucial when a vehicle is further developed over several seasons.


Programming MoTeC Tune ECU and PDM in one software. Matlab Simulink style.


Library of pre-built functions

The COMPUTE Wizard provides a library of ready-made functions for standard tasks such as windshield wipers or turn signals. Instead of building this logic from scratch each time, the function is selected, parameterized, and assigned to the pins. This significantly reduces the basic configuration of a vehicle – time is then spent on project-specific functions where it belongs.



Measure while you build

SCOPE allows you to visualize COMPUTE signals live while the configuration is being developed. Build, view, test – all within the same interface. Later, SCOPE becomes a diagnostic tool for troubleshooting vehicle problems.

The environment is complemented by a graphical representation of the CAN network and keypad layout, as well as a dynamic pinout visualization in the help section. This reduces one of the most common sources of error in wiring harness construction: the discrepancy between documentation and actual pin assignment.

Diagnostics of electrical systems in vehicles. Oscilloscope view to locate faults.


Communication and data collection

The PDM40 is not just a distribution point, but a fully-fledged network node. Four CAN buses with switchable termination – two of which are CAN FD-capable – connect ECUs, dashcams, keypads, and third-party devices. In addition, it features a 10/100 Ethernet port, two automotive Ethernet interfaces (100/1000Base-T1), and two serial ports for RS232, TTL, or LIN.

CAN messages are dynamically imported and exported via the COMMS subsystem. This significantly simplifies integration into existing vehicle networks and series components.


The integrated wideband lambda inputs, analog and digital inputs, and internal IMU make the PDM40 a data acquisition device in addition to its primary function. Logging operates at M1 level and is analyzed using standard MoTeC tools. This eliminates the need for a separate logger or additional data acquisition module in many vehicles.



Far beyond motorsport

The features that distinguish the PDM40 in race cars – robustness, precise current measurement, programmable logic, and open communication – are also in demand in other industries. Maptec already serves numerous customers in these areas:

  • Sports cars and limited-production vehicles: One control unit replaces the fuse box, relays, and additional modules. Fewer components, less wiring harness, cleaner diagnostics.

  • Industrial development: Prototypes and test vehicles benefit from rapid configuration and live measurement. Functions can be developed iteratively without hardware modifications.

  • Test bench and measurement electronics: Power supply, sequence control and data acquisition in one device. The Ethernet interfaces facilitate connection to test bench computers.

  • Aviation: Low weight, IP67 rating, and seamless monitoring of every consumer are particularly valuable in experimental and special applications. Not approved for certified aircraft.

  • Defense and special vehicles: Robust construction, operation up to 6 V and flexible wake-up strategies meet high availability requirements.

  • Alternative drives and EVs: Control of pumps, fans and auxiliary units, integration via CAN FD and Automotive Ethernet, and a sophisticated standby management system.

  • Municipal and commercial vehicles: Hydraulics, lighting, attachments and keypads can be centrally controlled and diagnosed.


Visual programming pays off especially outside of motorsport: Even complex process controls remain comprehensible and documentable for development teams.

Safety and power control for industry, aviation, development and research


Maptec: Your partner for the MoTec PDM40

Maptec has been an official MoTeC dealer for a decade and brings two decades of experience in motorsport electronics, calibration, and tuning. We design and build wiring harnesses, configure ECUs, PDMs, and dashes, and tune vehicles on the dyno and at the track.

For the PDM40, this means specifically:


  1. System design: We define channel allocation, current classes and protection to suit your vehicle or application.


  2. Configuration: We implement your functions in COMPUTE – from basic configuration to customer-specific control strategies.


  3. Integration: We integrate the PDM40 into your existing system via CAN, Ethernet and LIN bus, whether MoTeC environment or third-party components.


  4. Commissioning and support: We validate the system with measurements and support you during operation.


The MoTeC PDM40 will be available from Q2 2027. Are you planning a new project or would you like to upgrade an existing system? Contact us for a free consultation: info@maptec.ch or +41 71 552 00 50.


Source of technical data: MoTeC PDM40 – First Look . All information is preliminary; MoTeC reserves the right to make changes.

 
 
 

Comments


contact us

Contact us today

Thank you for your message!

Maptec_Wortmarke_200720_RGB.png

Chiptuning / consumption optimization and individual adjustments

In the autobau Romanshorn, where every car heart beats faster.

  • w-facebook

© Copyright Maptec 2019

bottom of page